<em id="8ljgl"><object id="8ljgl"><input id="8ljgl"></input></object></em>

<tbody id="8ljgl"></tbody>

    1. <tbody id="8ljgl"><p id="8ljgl"></p></tbody>
      <s id="8ljgl"></s>

      <th id="8ljgl"></th><em id="8ljgl"><acronym id="8ljgl"><input id="8ljgl"></input></acronym></em>
    2.  


      pricing5
      pricing4
      pricing3
      pricing2
      pricing1


      The heavier piston, turbo-prop and jet powered aircraft weighing up to 32000 lbs. (14517kg) are too valuable to consider using anything less than the A700 Series Aircraft Jacks from Meyer Hydraulics. For over 55 years, we have been manufacturing aircraft jacks that continue to set the standard for safe, dependable lifting at affordable prices. This Series of professional hydraulic lifting equipment handles airplanes and helicopters with the security and features one should demand in an aircraft jack.


      A: INNER SLIDE TUBE - The 3.5" (89mm) diameter powder-coated Tube forms the foundation of the TriTask Aircraft Jack System. The zigzag pattern of 1" (25mm) safety lock-out holes are vertically spaced 1.5" (38mm). The Tube's top has a 1" (25mm) diameter threaded hole designed to receive an AT-JPRn Jacking Point Receiver, a Top-of-the-Jack Load Cell or an AT-EBnnn Extension Bar.
      B: POSITIVE SAFETY LOCK - Spring-loaded safety pin "pops" into the Inner Slide Tube and rests on top of the Jack's frame to prevent the accidental lowering of the aircraft.
      C: ANTI-SNAG ROUND FRAME TUBE has a 4.5" (114mm) diameter with
      a 3.5" (89mm) ID that lowers about .125" (5mm), and uniquely contacts the hanger floor as the aircraft is being lifted.
      D: LOW-HEIGHT LEG DESIGN provides maximum gear door clearance. The three legs insure excellent stability with about 47" (120cm) leg-to-leg spread and each leg tip out 27" (68.6cm) from the center of the round frame tube. This provides a minimum of 27" (68.6cm) on one side and 14.5"
      (36.8cm) on the other for side-to-side support. Contact Meyer Hydraulics if your gear door clearance is less than 2.375" (60mm) from the center of the aircraft's jacking point.
      E: SIX 3" (76mm) SPRING LOADED CASTERS allow easy transporting of the Jack around the hanger without the need for the steel legs to scuff across the floor.
      F: TWO ACCESSORY TUBES are provided to allow the operator to put in accessories or tools for on-board storage if desired.
      G: LEG FLOOR PADS each provide a 4" x 2" (10x5cm) surface area for load
      distribution and to help prevent hanger floor surface damage.


      TriTask Jack &
      Inner Slide Tube
      Low Height
      (Tube only)
      Low Height
      w/AT-JPR2*
      Hydraulic Stroke High Height
      (Tube only)
      High Height
      w/AT-JPR2*
      A722B w/AT72222* 22.125" (56.2cm) 22.5" (57.2cm) 14" (35.6cm) 36.125" (91.8cm) 36.5" (92.7cm)
      A725B w/AT72525* 25.125" (63.8cm) 25.5" (64.8cm) 17" (43.2cm) 42.125" (107cm) 42.5" (108cm)
      A728B w/AT72828* 28.125" (71.4cm) 28.5" (72.4cm) 20" (50.8cm) 48.125" (122.2cm) 48.5" (123.2cm)
      A728C w/AT72828* 28.125" (71.4cm) 28.5" (72.4cm) 20" (50.8cm) 48.125" (122.2cm) 48.5" (123.2cm)
      A734B w/AT73434* 34.125" (86.7cm) 34.5" (87.6cm) 26" (66cm) 60.125" (152.7cm) 60.5" (153.7cm)
      A734C w/AT73434* 34.125" (86.7cm) 34.5" (87.6cm) 26" (66cm) 60.125" (152.7cm) 60.5" (153.7cm)
      A740C w/AT74040* 40.125" (101.9cm) 40.5" (102.9cm) 31" (78.7cm) 71.125" (180.7cm) 71.5" (181.7cm)
      A755C w/AT75555* 55.125" (140cm) 55.5" (141cm) 40" (101.6cm) 95.125" (241.6cm) 95.5" (242.6cm)
      (Special leg bracing and extra casters make the A755C ideal for lifting flight simulators as well as aircraft)
      A760A w/AT75560* 60" (152.4cm) 60.375" (153.4) 40" (101.6cm) 100" (254cm) 100.375" (255cm)

      *Comes standard with that TriTask Jack



      A722B 16000 lbs. (7258kg)
      A725B 16000 lbs. (7258kg)
      A728B 16000 lbs. (7258kg)
      A728C 24000 lbs. (10886kg)
      A734B 16000 lbs. (7258kg)
      A734C 24000 lbs. (10886kg)
      A740C 24000 lbs. (10886kg)
      A755C 24000 lbs. (10886kg)
      A760A 10000 lbs. (4536kg)




      The most advanced and versatile aircraft lifting system for
      maintenance professionals servicing airplanes and helicopters
      weighing up to 32000 lbs. (14517kg)
      image1
      image1
      The Inner Slide Tubes
      The new TRITASK Aircraft Jacks with their powder-coated
      Inner Slide Tubes form the "anchor" of the new TriTask System.
      leftThe top of the A600 and A700 Series Inner Slide Tubes are designed to receive an AT-JPRn, AT-EBnnn or a top-of-the-jack aircraft weighing Load Cell.
      leftThe Inner Slide Tubes for the A500 Series have a built-in 1.25" (32mm) round Jacking Point receiving socket machined into the top of its protruding anchoring stud.The AT500-CA Conversion Adapter can be mounted on the anchoring stud, which will then allow the A500 Series Inner Slide Tubes to function the same as the A600 and A700 Series Inner Slide Tubes.
      left
      Top portion of A600 and
      A700 Series Inner Slide Tube
      left
      Top portion of A500 Series
      Inner Slide Tube
      image1
      left


      AT-JPR1 in an A600 or A700 Series Aircraft Jack Inner Slide Tube
      left

      AT-JPR2 in an
      AT500-CA
      Conversion
      Adapter
      for the
      A500 Series
      AT-JPRn Jacking Point Receivers
      Made of solid steel and powder-coated with a long-lasting yellow finish for easy spotting, these JPR Receivers have been designed to be put into the top of an A600 or A700 Series Aircraft Jack's Inner Slide Tube, an AT-EBnnn Extension Bar or the AT500-CA Conversion Adapter for the A500 Series. The AT-JPR1 is a 1.5" x .187" (38x5mm) pad with a .875" (22mm) round Jacking Point receiving socket. The AT-JPR2 is a little larger with a 1.75" x .375" (44x10mm) pad with a 1.25" (32mm) round receiving socket. Both have a 1" x 1" (25.25mm) round stem.
      image1
      left

      AT500-CA Conversion Adapter, Mounted on top of an A500 Inner Slide Tube
      left

      Mounting Load Cell in AT500-CA Conversion
      Adapter
      Mounted to an
      A500 Inner Slide Tube
      AT500-CA Conversion Adapter
      This optional 2.25" (57mm) round steel
      powder-coated Adapter only connects to the A500 Series Inner Slide Tubes and adds .875" (22mm) to the height of the Jack. After securing the Adapter to the Inner Slide Tube's protruding anchoring stud, an AT-JPRn, AT-EBnnn or a top-of-the-jack aircraft weighing Load Cell can be quickly put into the top of the Conversion Adapter.
      Mounting the AT500-CA Conversion Adapter to an A500 Inner Slide Tube
      image1
      left

      AT-EBnnn screwed
      into an AT500-CA
      Conversion
      Adapter
      on top of
      an A500 Series
      Inner Slide Tube
      left

      AT-EBnnn with an
      AT-JPRn in an A600 or A700 Aircraft Jack's Inner Slide Tube
      left
      AT-EB015 thru AT-EB125 Extension Bars Extends the height of the TriTask Jack so technicians can get close to the airplane or helicopter without wasting valuable hydraulic lifting stroke.
      AT-EBnnn Extension Bars
      Twelve (12) optional 1.75" (44mm) solid steel
      powder-coated Extension Bars of various lengths screw into the top of an A600 or A700 Aircraft Jack's Inner Slide Tube or into the AT500-CA Conversion Adapter used on the A500 Series. They extend the height of the Jack 1.5" to 12.5" (38 to 318mm) in 1" (25mm) increments. Both of the AT-JPRn Jacking Point Receivers or a top-of-the-jack aircraft weighing Load Cell can quickly be put into the top non-threaded hole of an
      AT-EBnnn Extension Bar. The AT-EBnnn's cannot be used on the A755C and A760A Aircraft Jacks.
      image1
      image1
      Built-in Ability to use a
      Top-of-the-jack Helicopter and
      Airplane Weighing Load Cell
      A Load Cell with the standard 1" x 1" (25x25mm) round
      stem can be quickly put into the top of an A600 or
      A700 Series Aircraft Jack's Inner Slide Tube, an
      AT-EBnnn Extension Bar or the top of an AT500-CA
      Conversion Adapter used on the A500 Series.

      Meyer Hydraulics does not make or distribute aircraft
      weighing Load Cells or Scales. These are readily available
      from other sources, such as one of our Select Distributors
      or Jackson Aircraft Weighing Scales.
      left
      A500 Inner Slide Tube with AT500-CA Conversion Adapter, AT-EB025 Extension Bar and Load Cell
      left
      Mounting Load Cell in
      an A600 or A700 Series
      Inner Slide Tube


      上下分麻将平台